 |
250K Balance/Blend Split Shaft Control Pots
Split knurled shaft with coarse splines. Shaft Diameter: .232"
Body Dia: 5/8" • Body Height: 3/8" • Shaft thread length: 3/8"
Use to blend passive pickups.
ALPS 250K Audio Taper: $11.95 each 
ALPS 250K Linear Taper: $11.95 each
|
 |
250K Split Shaft Pots with DPDT Push-Pull Switch
Body Diameter: 5/8". Threaded Bushing Length: 3/8".
Shaft Spline Length: 3/8". Mounting Hole Size: 3/8"
These can be used as a normal volume or tone control, and they also pull up to activate an on/on double-pole double-throw (DPDT) mini switch which is used for coils splitting, reverse phase switching and other functions. 6mm split knurled shaft with coarse splines fits most import style knobs.
Alpha 250K Audio Taper: $11.95 each
|
 |
250K Solid Shaft Pot with DPDT Push-Pull Switch
Body Diameter: 5/8". Threaded Bushing Length: 3/8".
Shaft Length: 3/8". Mounting Hole Size: 3/8". Pull up to activate an on/on double-pole double-throw (DPDT) mini switch which is used for coils splitting, reverse phase switching and other functions. Short smooth solid shaft for knobs with set screws.
Alpha 250K Linear Taper: $11.95 each
|
 |
250K DPDT Push-Pull Switch Plug-in Module
Body Diameter: 5/8". Threaded Bushing Length: 3/8".
Shaft Length: 3/8". Mounting Hole Size: 3/8". Pull up to activate an on/on double-pole double-throw (DPDT) mini switch which is used for coils splitting, reverse phase switching and other functions. 6mm split knurled shaft with coarse splines fits most import style knobs.
Alpha 250K Audio Taper: $11.95 each
Alpha 250K Audio Taper: $19.95 two units
Alpha 250K Audio Taper: $26.95 three units
|
 |
Dual 250K Stacked Concentric Control Pots
24mm (7/8") body diameter. 1/4" smooth solid shaft for set screw knobs. 8MM bushing. Shaft length: 0.33" . Mounting Hole: 0.323"
Alpha 250K - 250K Audio Taper: $4.95 each
Alpha 250K - 250K Linear Taper: $4.95 each
|
 |
250K-250K Stacked Concentric Control Pots
7/32" Upper Shaft - 5/16" Lower Shaft, center detent.
Metric nuts and washers.
250K - 250K Audio Taper: $11.95 each
|
 |
250K-500K Stacked Concentric Control Pots
Typically used in the '62 Jazz bass 3-hole control plate for volume and tone under one knob. Top knob controls 250K audio pot, bottom knob controls 500K audio pot. 1/4" threaded shaft length for pick guard and control plate mounting. Top shaft is 3/16" diameter. Bottom shaft is 17/64" diameter. Requires a 3/8" mounting hole.
CTS 250K - 500K Audio Taper: $12.95 each
|
 |
250K Long Split Shaft Volume or Tone Control Pots
Body Diameter: 7/8". Threaded Bushing Length: 3/4".
Shaft Spline Length: 3/8". Mounting Hole Size: 3/8"
Split knurled shaft with fine splines fits most USA knobs. 3/4 inch threaded shaft length for use on instruments with thick tops.
CTS 250K Audio Taper: $8.95 each
|
 |
250K Short Solid Shaft Control Pots
Body Diameter: 7/8". Threaded Bushing Length: 3/8".
Shaft Length: 0.33". Mounting Hole Size: 0.375"
Audio taper pots are used for volume or tone controls, whereas linear taper pots are typically only used for tone controls. Requires a Control Knob with a 1/4" diameter hole with a Set Screw.
CTS 250K Audio Taper: $4.95 each
|
 |
250K Short Split Shaft Control Pots
Typically used with single coil pickups. Audio taper pots are used for volume or tone controls, whereas linear taper pots are typically only used for tone controls. Requires 3/8" mounting hole. 6mm split shaft with 3/8" long threaded bushing. Requires either a 6mm Push-on Control Knob or can also use a 6mm Knob with a set screw or a 1/4" Control Knob with a set screw and a brass sleeve.
CTS 250K Audio Taper: $4.95 each
CTS 250K Linear Taper: $4.95 each
CTS Lefty 250K Audio Taper: $5.50 each
CTS Lefty 250K Linear Taper: $5.50 each
|
 |
250K Short Solid Shaft Control Pots
Used as a normal volume or tone control on active systems.
Body Diameter: 24mm. Bushing Diameter: 3/8"
Shaft Length: 0.33". Mounting Hole Size: 0.375"
1/4" smooth solid shaft for set screw knobs.
Alpha 250K Audio Taper: $2.95 each
Alpha 250K Linear Taper: $2.95 each
|
 |
Fender No-Load 250K Tone Control Pots
CTS manufactured. Works like a standard 250K pot 1-9 but "clicks" in at 10 (full clockwise) and takes the pot out of the circuit entirely. This eliminates the path to ground that exists with standard pots in the full setting. The result is increased power and brightness at the "full on" setting. 1/4" threaded shaft length for pickguard and control plate mounting. |
If 250K pots are used, the load is reduced from 125K to 250K and if 500K pots are used, the load is reduced from 250K to 500K (high resistance = low load) The reduced load allows more power output from the pickup and reduces the amount of high frequencies that bleed off to ground. This gives a noticeable increase in brightness and output in the full treble setting. The no load pot can be used in place of any standard tone control on any guitar or bass.
CTS 250K Audio Taper Solid Shaft: $7.95 each
CTS 250K Audio Taper Split Shaft: $7.95 each
|
 |
250K Mini Short Split Shaft Control Pots
Requires 3/8" mounting hole. 6mm split shaft with 3/8" long threaded bushing. Requires either a 6mm Push-on Control Knob or can also use a 6mm Knob with a set screw or a 1/4" Control Knob with a set screw and a brass sleeve.
CTS 250K Audio Taper: $4.75 each
|
 |
250K Short Shaft Mini Control Pots
Shaft Diameter: 1/4" -|- Shaft length: 0.33"
Body Diameter: .63" (16mm). Mounting Hole: 0.29"
Alpha control pots are known for great quality and are popular with many guitar manufacturers. These "mini" size pots are perfect for smaller cavities and pickguard mounted controls.
Most commonly used with single coil pickups.
Alpha 250K Audio Taper Split Shaft: $2.50 each
Alpha 250K Linear Taper Split Shaft: $2.50 each
Alpha 250K Audio Taper Solid Shaft: $2.50 each
|
>>> Wiring Components >> Potentiometers > 250K Bass Guitar Control Pots
|
|
)
)
)
)
)
)
)
)
)
)
)
)
)
)
)
