zoom |
Prewired P-Bass Control Harness with CTS Pots, etc.
Highest quality P-Bass replacement wiring harness. These are suitable for any bass guitar. Includes two CTS 250K audio taper solid shaft pots, one Sprague Orange Drop .047µF capacitor, |
one Switchcraft 1/4" mono output jack, your choice of 22 guage wire, plus 1/2 sheet (4" x 12") of copper foil shielding for pickguard and ground wire, and shrink wrap tubing. IF you need enough copper foil to shield the remainder of the rear of your pickguard, you can order another half sheet of the foil below and I'll send you a full 8" x 12" sheet.
Wired to Standard Fender P-bass specifications and completely ready to install. Solder is optional for the pickup wires as you can use solderless pin connectors (not included).
You can read further explanations of the copper foil for the ground wire and the shrink wrap tubing on the Jazz bass harness.
CTS 250KA SOLID Shaft Pots
WBE 22awg PVC Covered Stranded Copper Wire: $39.95 
Vintage Cloth Covered 22awg Stranded Copper Wire: $42.95
WBE PTFE 22awg Teflon High Temp Silver Plated Wire: $44.95
1/2 sheet Copper Foil: 4" x 12": $3.95
CTS 250KA SPLIT Shaft Pots
WBE 22awg PVC Covered Stranded Copper Wire: $39.95
Vintage Cloth Covered 22awg Stranded Copper Wire: $42.95
WBE PTFE 22awg Teflon High Temp Silver Plated Wire: $44.95
1/2 sheet Copper Foil: 4" x 12": $3.95
|
Vintage Style |
Prewired P-Bass Control Harness with Gold Pin Connectors
Everything is the same as above but terminated with gold plated male and female pin connectors. |
There's also a choice with the pin connectors where you can have the connectors soldered to the harness side and two unsoldered connectors or with both connectors soldered as shown in the photo. You will also receive one additional set of gold pin connectors (two male and two female). Send me an email or make a note in the Cart as to how you want your connectors.
CTS 250KA SOLID Shaft Pots
WBE 22awg PVC Covered Stranded Copper Wire: $49.95
Vintage Cloth Covered 22awg Stranded Copper Wire: $52.95
WBE PTFE 22awg Teflon High Temp Silver Plated Wire: $55.95
1/2 sheet Copper Foil: 4" x 12": $3.95
CTS 250KA SPLIT Shaft Pots
WBE 22awg PVC Covered Stranded Copper Wire: $49.95
Vintage Cloth Covered 22awg Stranded Copper Wire: $52.95
WBE PTFE 22awg Teflon High Temp Silver Plated Wire: $55.95
1/2 sheet Copper Foil: 4" x 12": $3.95
|
zoom |
Prewired Control Harnesses with Alpha Dime-Size Pots
Replacement wiring harness for any bass requiring small diameter pots and small diameter output jack due to the limited size of the control cavity. Includes Alpha 250K audio taper split shaft pots, Xicon polyester film .047µF capacitor, 1/4" mono output jack, 22 guage PVC wire, 1/2 sheet (4" x 12") of copper foil shielding for pickguard and ground wire, and shrink wrap tubing. |
Wired to Standard Fender P-bass specifications and completely ready to install. Solder is optional for the pickup wires as you can use solderless pin connectors (not included).
View a closeup of the wiring without the copper foil screwing up the photo. IF you need enough copper foil to shield the remainder of the rear of your pickguard, you can order another half sheet of the foil below.
|
>>> Wiring Components >> Prewired Harnesses > P Bass Control Harnesses
Also see: Bass PreAmps & Prewired Assemblies and Prewired Pickguards with Pickups
|
|
)
){kind=small}
)
){kind=link}